Product#: K919

1967-2004 Buick, Chevy, Oldsmobile, Pontiac; Accelerator Pedal; Various GM Models

1976-1976 Chevrolet Pickup Truck (C/K Series) (1st Design) 1971-1972 Chevrolet Blazer 1976-1976 Chevrolet Blazer (1st Design) 1979-1984 Chevrolet G10, G20, G30 Series Van 1979-1984 Chevrolet P10, P20, P30 Series Van...

Product#: K521

1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models

OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...

Product#: 368077

1967-2002 Buick, Chevrolet, Pontiac, Oldsmobile; Accelerator Pedal Tension Spring; Various Car and Truck Models

This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...

Product#: AL124

Accelerator Throttle Rod; Universal Fit

Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...

Product#: K518

1967 Firebird; Accelerator Pedal Assembly; V8; 326ci, 400ci

Reproduction of the complete accelerator pedal assembly which extends from the firewall on all V8-equipped 1967 Firebird models. This accelerator pedal assembly comes complete with the pedal, pedal mount pin and spring,...

Product#: PY4206

1971-74 Trans-Am Throttle Cables

These throttle cables have the correct ends (carburetor and accelerator pedal) and look very close to the original.

Product#: PY4216

1970 Firebird, Trans Am; Accelerator Lever Cable; 350, 400, 455 HO, or Ram Air

Reproduction accelerator lever cable for 1970 Firebird and Trans Am models with 350, 400, 455 HO or Ram Air. This cable extend from the accelerator to the throttle arm. If your original cable shows signs of fraying or...

Product#: CB5379F

1967 Firebird; Quadrajet Throttle Arm; For V8

Reproduction 1967 Pontiac Firebird throttle lever arm, also known as the carburetor lever extension. This is the throttle arm bracket that is used only on 1967 Firebird V8 equipped models with 4 barrel Quadrajet carburetor....

Product#: 9789015

1967 Pontiac Firebird; Accelerator Pedal Rod ; with V8

Reproduction of the original accelerator pedal rod designed for use on 1967 Firebird models with V8 engines. The pedal rod is the final link in your Firebird models accelerator/throttle activation system. This special rod...

Product#: 9789018

1967 Firebird; Accelerator Pad To Rod Support; OE Style Steel Reproduction

Reproduction of the original accelerator pad to rod support designed for use on 1967 Firebird models. This is the support that bolts to the firewall and holds the accelerator pedal shaft. This item will replace your often...

Product#: 340637

1974-81 Outer Accelerator Pull Spring

Correct reproduction of the commonly missing or worn out outer accelerator pull spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Manufactured to exact factory...

Product#: K912

1967-2004 Buick, Chevy, Pontiac, Olds; Accelerator Pedal Pad Trim Plate; Stainless Steel; Various Models

Reproduction of the original accelerator pedal trim plate designed for use on various GM models. Manufactured to exact factory dimensions, each trim plate is stamped in quality stainless steel offering a supurb appearance....

Product#: 3909978

1967 Chevy, Pontiac; Accelerator Pad; with Steel Backing Plate; OE Style; Various Models

Reproduction of the original accelerator pedal pad designed for use on various 1967 GM models. This accelerator pedal pad is manufactured in the correct design based on a steel backing unlike the GM plastic replacements. The...

Product#: 9789456

1967 Firebird; Accelerator Throttle Arm; V8; 326ci, 400ci

Correct reproduction of the original accelerator throttle arm designed for use on 1967 Pontiac Firebird V8 models. Manufactured in stamped steel to OE specifications, each throttle arm features correct contours that provide...

Product#: 14876

1970-72 Camaro, Firebird; Accelerator Cable Bracket; with Holley Carburetor

Reproduction accelerator throttle cable bracket for 1970-72 Camaro and Firebird models with Holley Carburetor. This quality bracket is manufactured in stamped steel to the original factory configuration. Will fit and install...

Product#: P145

1967-69 F-Body; 68-74 Nova - Billet Throttle Assembly with Black Anodized Finish

Manufactured from solid aluminum, each billet throttle assembly is fully adjustable featuring a uniquely designed molded rubber insert, and spring loaded pedal. Made in USA Each assembly is anodized with machined highlights.

Product#: FM6098

Lokar Eliminator Brushed Billet Aluminum Floor Mount Gas Pedal with Rubber Inserts

The Eliminator floor-mount gas pedal is precision crafted from billet aluminum and designed to eliminate routing cables through the firewall. Includes an adjustable aluminum splined shaft and stainless steel under-the-floor...

Product#: FM6097

Lokar Eliminator Brushed Billet Aluminum Floor Mount Gas Pedal with Ball Milled Finish

The Eliminator floor-mount gas pedal is precision crafted from billet aluminum and designed to eliminate routing cables through the firewall. Includes an adjustable aluminum splined shaft and stainless steel under-the-floor...

Product#: BAG6096

1967-69 Camaro / Firebird Lokar Billet Accelerator Pedal Assembly - Brushed w/Rubber Inserts

Lokar 1967-69 Camaro & Firebird billet aluminum throttle pedal assembly is designed to bolt into the stock location on the firewall, allowing you to change from the factory rod linkage to a modern throttle cable set up. The...

Product#: B199165

1967-69 Camaro/Firebird Billet Specialties Billet Aluminum Cable Style Gas Pedal Assembly - Black

Add a touch of class to the interior of your 1967-69 Camaro or Firebird with one of these CNC machined cable style gas pedal assemblies from Billet Specialties. These pedals convert your old linkage to a more modern cable...

Product#: B199160

1967-69 Camaro/Firebird Billet Specialties Billet Aluminum Cable Style Gas Pedal Assembly - Polished

Add a touch of class to the interior of your 1967-69 Camaro or Firebird with one of these CNC machined cable style gas pedal assemblies from Billet Specialties. These pedals convert your old linkage to a more modern cable...

Product#: BG6004

Lokar Black Anodized Aluminum Throttle Assembly Standard 1-1/2" x 4" Pedal Pad with Rubber Inserts

Gleaming polish not your style? Then take a look at this stealthy black anodized billet spring-loaded throttle assembly that features a removable lower arm and is splined for versatile mounting to either the right or left...

Product#: BG6096

1967-69 Camaro / Firebird Lokar Billet Accelerator Pedal Assembly - Black with Rubber Inserts

Lokar 1967-69 Camaro billet aluminum throttle pedal assembly is designed to bolt into the stock location on the firewall, allowing you to change from the factory rod linkage to a modern throttle cable set up. The traditional...

Product#: D1950

Street Demon; Throttle Solenoid Set

Some vehicles, especially vehicles with air conditioning, require a throttle solenoid to automatically increase engine rpm. This throttle solenoid set from Demon Fuel Systems includes the solenoid, bracket, and mounting nut....

Product#: TF801171

1994 & Later LT1/LT4 - Black Stainless Steel Lokar Throttle and Kickdown Cable Bracket Set

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Product#: SR4015

Lokar Throttle Cable Bracket Set - Ram Jet 350 Small Block - Black Stainless Steel

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: TF801170

1992-93 LT1 - Black Stainless Steel Lokar Throttle and Kickdown Cable Bracket Set

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Product#: SR4014

Lokar Throttle Cable Bracket Set - Ram Jet 350 Small Block - Stainless Steel

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: TF801167

1992-93 LT1 Lokar Stainless Steel Throttle and Kickdown Cable Bracket Set

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Product#: BG6092

1967-69 Camaro / Firebird Lokar Billet Accelerator Pedal Pad - Flat Style - Black w/Rubber Inserts

Lokars traditional flat style billet aluminum throttle pedal pad lets you retain the factory throttle linkage, with a updated look inside the car. The direct fit throttle pad replaces the factory pad, measures 2" x 5" and...

Product#: E8030

Edelbrock Small Block Chevy Throttle/Cruise Control/Kickdown Bracket - Chrome Plated

Edelbrock throttle, cruise control, and transmission kick down set for pre-1978 small block Chevy cars with a TH350, 200R4, or 700R4 transmission. Manufactured in stamped steel and either chrome or gold cadmium plated....

Product#: SR4012

Lokar Throttle Cable Bracket - 2000-02 LS1 Engines w/3-1/2" Throttle Linkage Cam - 1 Hole - Black

Black Billet Aluminum. Single Hole Stud For Throttle Cable Only. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor brackets...

Product#: TF801166

Lokar Throttle Cable Bracket - 1985-91 TPI Engines - Triple Hole - Black Finish

This billet aluminum cable bracket from Lokar mounts to the side of your TPI intake plenum and allow you to install your throttle cable. Made in USA Black billet aluminum. Triple hole stud for throttle, kickdown, and cruise...

Product#: SR4008

Lokar Throttle Cable Bracket - 1998-99 LS1 Engines w/3" Throttle Linkage Cam - Single Hole - Black

Black Billet Aluminum. Single Hole Stud For Throttle Cable Only. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor brackets...

Product#: PY4205

1975-79 Firebird Throttle Cables With Pontiac Engine

These throttle cables have the correct ends (carburetor and accelerator pedal) and look very close to the original.

Product#: SR4018

Lokar Throttle Cable Bracket - 2000-02 LS1 Engines w/3-1/2" Throttle Linkage Cam - 1 Hole - Brushed

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: SR4007

Lokar Throttle Cable Bracket - 1998-99 LS1 Engines w/3" Throttle Linkage Cam - Dual Hole - Brushed

Brushed Billet Aluminum. Dual Hole Stud For Throttle Cable & Cruise Control Cable. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more....

Product#: PY4208

1978-79 Firebird Throttle Cables With 403 Engine

These throttle cables have the correct ends (carburetor and accelerator pedal) and look very close to the original.

Product#: C938531

1968-69 Firebird; Accelerator Pedal Lever; with V8 or 6 cyl.

Reproduction of the original accelerator pedal lever Pontiac used on 1968-69 Firebird models with either a 6 cyl. or 8 cyl. engine. This lever mounts at the firewall with the accelerator pedal mounting to one end and the...

Product#: DC2083

2 and 4 Bbl Holley Throttle Return Spring Set

Fits Holley 2300 and 2305 2 bbl. or Holley 4150 and 4160 4 bbl. carburetors mounted on any manifold. {fitment}

Product#: C894571

1967 Firebird; Accelerator Rod with Swivel V8; with 4 barrel Carburetor

Reproduction of the original carburetor accelerator rod designed for use with 1967 Firebird 8 cylinder 4 barrel carburetor models. Each bracket is manufactured in stamped steel to the original factory dimensions offering an...

Product#: D1953

Street Demon; Throttle/Transmission Kickdown Cable Bracket Set

This throttle and transmission kickdown cable bracket set removes the guesswork when installing a Street Demon carburetor in almost any carbureted GM application. All brackets have a clear zinc coating for corrosion...

Product#: T9756

Chevrolet Small Block; Chrome Accelerator Cable Bracket; TH350

Chrome plated bracket set for Chevy small block with throttle cable type linkage. May be used with either round or square mounts. No need to remove carburetor for installation and allows for full adjustment. {specs} {fitment}

Product#: GPS6014

Lokar Billet Aluminum 3/4" Throttle Assembly Spacer

Pedal floor spacers are recommended when installing on vehicles with thick carpet or carpet padding. Made in USA

Product#: H260

1967-72 Firebird Cruise Control Servo Bellows

Reproduction cruise control servo bellows for 1967-72 Firebird models. Replacing your leaky servo bellows should be the first step in repairing a non-functional cruise control system. Manufactured using the correct rubber...

Product#: A9700101

1969-72 Camaro, Firebird; Throttle Solenoid Switch Retaining Clip; Cowl Induction, Shaker Hood

Correctly finished and accurate reproduction of the original throttle solenoid switch retaining clip for use with 1969 Camaro models. Manufactured with the correct diameter for proper installation. For.60" diameter switches...

Product#: G3794

94-98 Cruise Control Release Switch

Having trouble with your cruise control? Is it working intermittently or not at all? You may want to check the switch. This is the switch located on the brake pedal arm.

Product#: 154214

1955-1970 Accelerator Throttle Lever Arm Pinch Bolt Kit

Correct reproduction accelerator throttle lever to pedal rod pinch bolt kit, includes (1) 1/4-20 x 1-1/4" grade 5 bolt, nut & washer. GM Full Size passenger car applications: 1955-1970 Camaro applications: 1967-1969 Chevy...

Product#: TA4045

1977-79 Pontiac Trans Am; Oldsmobile 403; Throttle Return Spring; Carb Linkage To Throttle Bracket

Oldsmobile 403 engine throttle return spring. Installs from the carburetor linkage to the throttle bracket.

Product#: D1951

Street Demon; TPS Set

When using an electronic overdrive transmission, such as a 4L60E, with a carbureted engine, the transmission control unit requires a throttle position signal. This sensor bolts on to the carburetor and sends the proper signal...

Product#: P170

1970-81 Camaro/Firebird Billet Throttle Assembly with Black Anodized Finish

Manufactured from solid aluminum, each billet throttle assembly is fully adjustable featuring a uniquely designed molded rubber insert, and spring loaded pedal. Made in USA Each assembly is anodized with machined highlights.

Product#: BAG6004

Lokar Billet Aluminum Throttle Assembly Standard 1-1/2" x 4" Pedal Pad with Rubber Inserts

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Product#: BAG6001

Lokar Billet Aluminum Throttle Assembly with Standard 1-1/2" x 4" Pedal Pad and a Ball Milled Finish

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Product#: SG6016

Lokar Chrome Steel Throttle Assembly with Extra Large 2" x 5" Pedal Pad and Rubber Inserts

The first spring loaded pedals in the industry! This chromed steel throttle assembly is spring loaded like the OE design, and features a removable, splined lower arm for versatile mounting to the right or left of the bracket...

Product#: SG6007

Lokar Chrome Steel Throttle Assembly with Standard 1-1/2" x 4" Pedal Pad and Rubber Inserts

The first spring loaded pedals in the industry! This chromed steel throttle assembly is spring loaded like the OE design, and features a removable, splined lower arm for versatile mounting to the right or left of the bracket...

Product#: SR4017

Lokar Throttle Cable Bracket & Spring Set - Big Block 502 - Black Stainless Steel

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: TF801168

1994 & Later LT1/LT4 Stainless Steel Lokar Throttle and Kickdown Cable Bracket Set

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Product#: SR4016

Lokar Throttle Cable Bracket & Spring Set - Big Block 502 - Stainless Steel

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: BAG6092

1967-69 Camaro / Firebird Lokar Billet Accelerator Pedal Pad - Flat Style - Brushed wRubber Inserts

Lokars traditional flat style billet aluminum throttle pedal pad lets you retain the factory throttle linkage, with a updated look inside the car. The direct fit throttle pad replaces the factory pad, measures 2" x 5" and...

Product#: B199265

Billet Specialties Billet Gas Pedal Pad - Black

These CNC machined pedal pads are specifically designed to compliment your Billet Specialties gas pedal. Each pad includes all the stainless steel hardware needed for a quick and clean install. Note: Replaces factory pad.