Product#: PX40011

Pertronix Flame Thrower 8-Cylinder 40,000 Volt 1.5 Ohm Black Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: 7720

MSD; Power Grid 7; Ignition Control Only

The Power Grid Ignition Control has been specially designed to mount to the Power Grid System Controller box, part #7730/77303. This Ignition output only controller packs higher output than the current programmable...

Product#: 77303

MSD; Power Grid System; Controller Only; Black

The Power Grid Ignition System is the next evolution of our Programmable 7-Series Ignition Controls. The Grid incorporates an efficient 32 bit microcontroller and an all new software program, called MSD View, and is USB...

Product#: 8253

MSD; Blaster HVC II Ignition Coil; Blue

The latest coil to be built entirely in house at MSD is designed to be used with MSD 6 and SCI Series Ignition Controls. This coil utilizes an iron U-Core design with a segmented bobbin for improved voltage distribution. The...

Product#: 8252

MSD; Blaster HVC Ignition Coil; Blue; Universal

Coils have always had to compromise voltage output against current output. More voltage increases the initial ionization of the spark plug gap, but lowers the amount of current, or heat, that follows across the plug gap. When...

Product#: 75643

MSD; Stand Alone Solid State Relay Kit; 4 Channel; Black

Clean up your wiring with an MSD Solid State Relay Block. This module takes the place of 4 standard relays and eliminates unsightly wiring. 4 independent channels can be activated using either power or ground. Each channel is...

Product#: 7740

MSD; Power Grid CAN-Bus 4-Hub Connector; Red

This hub allows you to expand the Power Grid system with up to four accessory modules.Note: This part is legal for use on Uncontrolled (Non-Emissions Controlled) Vehicles or Racing Vehicles.

Product#: 140013

Accel; 1974-87; 48,000 Volt; HEI In-Cap Super Coil; Red And Yellow Wires

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability.

Product#: 140005

Accel; 1974-87; 45,000 Volt; HEI In-Cap Super Coil; Red And White Wires

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability.

Product#: PX60104

Pertronix 60,000 Volt 0.45 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it efficiently...

Product#: PX60130

Pertronix 60,000 Volts 3.0 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it efficiently...

Product#: 8732

MSD; Digital 2-Step Rev Control; For Digital 6AL

This 2-Step Rev Control could be added to give you the ability to switch to a low rpm limit to use on the starting line. Features two easy to read rotary dials that let you set the launch rpm in 100 rpm increments. There is...

Product#: 140001

Accel; 1955-74; 45,000 Volt; Super Coil; Ignition Coil

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability.

Product#: PX60103

Pertronix 60,000 Volt 0.32 Ohm Flame Thrower HC Ignition Coil

The Flame Thrower HC (high current) coil has an E-Core design which is rated at 60,000 volts with an ultra low.32 primary resistance and has a High Current design for a rapid charge rate. Made from 6063 T5 aluminum, it...

Product#: PX3000

1974-88 GM HEI In-Cap Mounted Pertronix Flame-Thrower Coil with Black, Yellow and Red Wires

This Pertronix Flame Thrower 50,000 volt E-Core coil features an optimized winding design to maximize spark gap current and available voltage. Includes all necessary hardware. When teamed with a Flame Thrower module (sold...

Product#: PX3001

1977-91 GM HEI In-Cap Mounted Pertronix Flame-Thrower Coil with Black, White and Red Wires

This Pertronix Flame Thrower 50,000 volt E-Core coil features an optimized winding design to maximize spark gap current and available voltage. Includes all necessary hardware. When teamed with a Flame Thrower module (sold...

Product#: PX40001

Pertronix Flame Thrower 8 Cylinder 40,000 Volt 1.5 Ohm Chrome Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: PX44011

Pertronix Flame Thrower III 8 Cylinder 45,000 Volt 0.32 Ohm Black Oil Filled Ignition Coil

The Flame Thrower III Coil is a rapid charge ignition coil to optimize the Ignitor III module. The Flame Thrower III is a traditional oiled filled canister for the "old school" appearance; but will work with modern day...

Product#: PX45111

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...

Product#: PX44001

Pertronix Flame Thrower III 8 Cylinder 45,000 Volt 0.32 Ohm Chrome Oil Filled Ignition Coil

The Flame Thrower III Coil is a rapid charge ignition coil to optimize the Ignitor III module. The Flame Thrower III is a traditional oiled filled canister for the "old school" appearance; but will work with modern day...

Product#: PX40111

PerTronix Flame Thrower 8 Cylinder 40,000 Volt 1.5 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: PX45001

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Chrome Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...

Product#: 140011

Accel; 1984-95; 48,000 Volt; HEI Remote Super Coil

This HEI remote mount Super Coil is engineered with optimized low resistance, high turns ratio windings around a M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts,...

Product#: PX40611

Pertronix Flame Thrower 6 Cylinder 40,000 Volt 3.0 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: A7700200

E-Core Remote Ignition Coil; Red

The TSP power coil is capable of delivering a longer and hotter spark with up to 70% more spark energy than stock ignition coils. Its convenient design easily mounts to fire walls, core supports and fender wells. It features...

Product#: H556152

Holley; Sniper; HyperSpark Ignition Coil

Sniper EFI HyperSpark ignition coil from Holley. This coil features an innovative connector and integrated bracket for a secure connection and simplified mounting. Its powerful 135mj of spark ensure complete combustion and...

Product#: A7700202

E-Core Remote Ignition Coil; Black

The TSP power coil is capable of delivering a longer and hotter spark with up to 70% more spark energy than stock ignition coils. Its convenient design easily mounts to fire walls, core supports and fender wells. It features...

Product#: A7700201

E-Core Remote Ignition Coil; Blue

The TSP power coil is capable of delivering a longer and hotter spark with up to 70% more spark energy than stock ignition coils. Its convenient design easily mounts to fire walls, core supports and fender wells. It features...

Product#: 9201038-DKHD

Walker Products; ThunderSpark Ignition Coil 920-1038; HEI Ignition

ThunderSpark Ignition Coils are precision made for superior performance and manufactured to meet or exceed all original equipment specifications. A full service kit contains not only the base sensor but also provides the...

Product#: 66942R

1974-87 Proform HEI Distributor Coil Cap and Rotor Set with Red Cap and 50,000 Volt Coil

50,000 Volt coil and premium hi-dielectric cap with brass terminals, and premium rotor.

Product#: 66942BK

1974-87 Proform HEI Distributor Coil Cap and Rotor Set with Black Cap and 50,000 Volt Coil

50,000 Volt coil and premium hi-dielectric cap with brass terminals, and premium rotor.

Product#: 8145

Accel; 1955-74; Yellow; 45,000 Volt; Superstock Breakerless Electronic Ignition Coil

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability.

Product#: 9201005-DKHD

Walker Products; ThunderSpark Ignition Coil 920-1005; HEI Ignition

ThunderSpark Ignition Coils are precision made for superior performance and manufactured to meet or exceed all original equipment specifications. A full service kit contains not only the base sensor but also provides the...

Product#: 7730

MSD; Power Grid System; Controller Only; Red

The Power Grid Ignition System is the next evolution of our Programmable 7-Series Ignition Controls. The Grid incorporates an efficient 32 bit microcontroller and an all new software program, called MSD View, and is USB...

Product#: 8250

MSD; 6 HVC Ignition Coil

Coils have always had to compromise voltage output against current output. More voltage increases the initial ionization of the spark plug gap, but lowers the amount of current, or heat, that follows across the plug gap. When...

Product#: 7564

MSD; Stand Alone Solid State Relay Kit; 4 Channel; Red

Clean up your wiring with an MSD Solid State Relay Block. This module takes the place of 4 standard relays and eliminates unsightly wiring. 4 independent channels can be activated using either power or ground. Each channel is...

Product#: 77403

MSD; Power Grid CAN-Bus 4-Hub Connector; Black

This hub allows you to expand the Power Grid system with up to four accessory modules.Note: This part is legal for use on Uncontrolled (Non-Emissions Controlled) Vehicles or Racing Vehicles.

Product#: PX60115

Pertronix 60,000 Volts 1.5 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it efficiently...

Product#: 8207

MSD; Blaster SS; 40,000 Volt Ignition Coil; Red

Don't let the compact size of the Blaster SS Coil fool you because it is packed with performance. The efficient E-core windings are designed to produce high amounts of current without sacrificing the voltage output. In fact,...

Product#: 8145C

Accel; 1955-74; Chrome; 45,000 Volt; Superstock Breakerless Electronic Ignition Coil

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability.

Product#: 140003

Accel; 1974-87; 45,000 Volt; HEI In-Cap Super Coil; Red And Yellow Wires

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability.

Product#: PX3002

1985-95 GM Remote Mounted HEI Pertronix Flame-Thrower Coil

This Pertronix Flame Thrower 50,000 volt E-Core coil features an optimized winding design to maximize spark gap current and available voltage. When teamed with a Flame Thrower module (sold separately) it produces 100% more...

Product#: 8202

MSD; Blaster 2 Series; 45,000 Volt Ignition Coil; Red

If you are looking to upgrade your stock coil or want to complement the performance of your MSD 5, 6 and 7 Series Ignition, the Blaster Coil is the right choice. The Blaster 2 Coil shares the same special windings and high...

Product#: PX45011

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Black Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...

Product#: 5526

MSD; Street Fire Coil

Street Fire Ignition Coil offers entry level spark output for your GM dual connector ignition. Mounts directly in place of the factory coil and accepts the factory connectors. Spark energy is increased thanks to improved...

Product#: PX40501

Pertronix Flame Thrower 6 Cylinder 40,000 Volt 3.0 Ohm Chrome Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: PX40511

Pertronix Flame Thrower 6-Cylinder 40,000 Volt 3.0 Ohm Black Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: 840221

MSD; Ignition Coil Cover; Extreme Output; Internal Coil

Product#: 8140

Accel; 1955-74; Yellow; 42,000 Volt; 1.4 Ohm Primary; Superstock Ignition Coil; Points

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability.

Product#: 9201003-DKHD

Walker Products; ThunderSpark Ignition Coil 920-1003; HEI Ignition

ThunderSpark Ignition Coils are precision made for superior performance and manufactured to meet or exceed all original equipment specifications. A full service kit contains not only the base sensor but also provides the...

Product#: 9201037-DKHD

Walker Products; ThunderSpark Ignition Coil 920-1037; HEI Ignition

ThunderSpark Ignition Coils are precision made for superior performance and manufactured to meet or exceed all original equipment specifications. A full service kit contains not only the base sensor but also provides the...

Product#: 9201004-DKHD

Walker Products; ThunderSpark Ignition Coil 920-1004; HEI Ignition

ThunderSpark Ignition Coils are precision made for superior performance and manufactured to meet or exceed all original equipment specifications. A full service kit contains not only the base sensor but also provides the...

Product#: 241190-BBVL

Holley LS Coil Covers; Pontiac Style Valve Covers; For LS Engine Conversion; 241-190

Holley's 2-Piece LS valve covers are a great way to update the look of your LS engine without the use of complicated adapter systems or the hassle of remote coil relocation. These modular LS valve covers feature an OE height,...

Product#: A5700219

OTB Gear Aluminum Finned Coil Cover - Polished Finish

Vintage style finned coil cover for your classic. Mounts with 1/4"-20 drive studs. Cast in aircraft grade A356 aluminum and polished to a high sheen.

Product#: 140017

Accel; 1986-01; 45,000 Volt; AC Delco Style DIS Ignition Coil

This AC/Delco style Super DIS Coil is re-engineered to be the only true performance AC/Delco style DIS coil. "Raised Dome" construction, section bobbin technology, highly specialized silicone magnetic steel core along with...

Product#: 8129

Accel; HEI Ignition Cap & Rotor Set

Distributor Cap & Rotor Set For over 30 years, ACCEL has been manufacturing distributor caps, rotors, points and condensers for racing applications world-wide. As a direct result of this racing involvement, ACCEL engineers...

Product#: 8140C

Accel; 1955-74; Chrome; 42,000 Volt; 1.4 Ohm Primary; Superstock Ignition Coil; Points

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability. Fits 1955-74 with breaker point ignition

Product#: 84039

MSD; 18"; Red; Super Conductor 8.5MM Coil Wire; With 90° Treminals

If you're changing a coil or cap to a new design, you could find yourself searching for different terminals for the coil wire. MSD offers this 18" long, 90° male coil terminals and boots are installed on both sides to...

Product#: 84033

MSD; 18"; Black; Super Conductor 8.5MM Coil Wire; With 90° Terminals

If you're changing a coil or cap to a new design, you could find yourself searching for different terminals for the coil wire. MSD offers this 18" long, 90° male coil terminals and boots are installed on both sides to...

Product#: 84049

MSD; 18"; Red; Super Conductor 8.5MM Coil Wire; With Straight Treminal

If you're changing a coil or cap to a new design, you could find yourself searching for different terminals for the coil wire. MSD offers this 18" long, straight female socket coil terminal and boot on one side with a...