Product#: E2692

Carburetor Adapter, Open Center, Spread Bore Carburetor to Square Bore 4 Barrel Manifold; 2692

This Edelbrock carburetor adaptor is designed to mount 4-bbl Rochester Quadra jet carburetors to square-bore, single plane intake manifolds. The adaptor weighs two pounds and one ounce and ships via UPS. 2692 Specifications:...

Product#: TD2044

Trans-Dapt Carburetor Adapter; Holley 2-Barrel Carburetor to Small 1-Barrel Manifold, 1.75 in. Thick, Open Center

Trans-Dapt Holley 2 barrel to to 1 barrel carburetor adapter. This adapt will install any 350, 500, 650 cfm carb with 2-5/8' bolt center to a Ford straight-six manifold. Includes carburetor adapter, gaskets, carb studs, nuts,...

Product#: 265030

Carburetor Wedge Plate

During hard acceleration the float bowls in a carburetor become uneven, causing moderate fuel starvation. This aluminum spacer tilts the carburetor forward 5 degrees to help keep it level. Spacer measures.830" at it's...

Product#: T2103

Holley 4150 Carb Spacer Kit; Open Center; 1" Tall; For PCV With 3/8" Fitting

Carburetor spacer kits are now available for Holley carburetors. Each kit includes mounting hardware and gaskets.

Product#: MG1932

Holley Square Bore 4-Barrel to Rochester Quadra-Jet 4-Barrel Craburetor to Manifold Adapter Kit

Holley square flange carburetor adapter kit for Rochester 4-barrel intake manifolds. This kit will adapt a square bore carburetor to spread bore Rochester Q-Jet or Carter Thermo Quad 4-barrel manifold. The adapter is 3/4"...

Product#: AR100701

Airaid; Poweraid Throttle Body Spacer; Holley 4BBL 4150/4160 & Edelbrock Square Flange OE

Enhance Mid-Range Power, Torque And Fuel Efficiency! The Poweraid Throttle Body Spacer is designed to cause a spinning action of the incoming air charge as it passes through the throttle body. This air charge carries all the...

Product#: AR100702

Airaid; Poweraid Throttle Body Spacer; Holley 2BBL 2300

Enhance Mid-Range Power, Torque And Fuel Efficiency! The Poweraid Throttle Body Spacer is designed to cause a spinning action of the incoming air charge as it passes through the throttle body. This air charge carries all the...

Product#: 9A589E

1963-68 Ford, Mercury; Carburetor to Manifold Spacer; with 6 Cyl; 1 BBL; 4C Trans; with Smog Pump

Correct replacement of the original carburetor spacer unit found on 1964-68 Mustangs with 6 cylinder engines. The spacer installs between the carburetor and the intake manifold. Designed specifically for 6 cylinder models...

Product#: T2094

Holley Carburetor Spacer Set; 3/8" Tall Open Center; With Vacuum Tube & Cap

Carburetor spacer kits are now available for Holley carburetors. Each kit includes mounting hardware and gaskets. {specs} {fitment}

Product#: T2084

Holley 4150 Phenolic Carb Spacer Kit; Open Center; 1" Tall; with Hardware and Gaskets

Phenolic carburetor spacer kit for Holley 4150 carburetors. Each kit includes mounting hardware and gaskets.

Product#: T2063

Holley "Hiker" Carburetor Spacer Set; 3/8" Tall Open Center

Carburetor spacer kits are now available for Holley carburetors. Each kit includes mounting hardware and gaskets. {specs} {fitment}

Product#: T2081

Holley 4150 Carb Spacer Kit; Open Center; 2" Tall

Carburetor spacer kits are now available for Holley carburetors. Each kit includes mounting hardware and gaskets.

Product#: TD2025

Trans-Dapt Carburetor Adapter; 2-Barrel Carburetor to 1-Barrel Manifold, 1-5/8". Tall, Open Center

Trans-Dapt 2 barrel to to 1 barrel carburetor adapter. This will adapt Rochester 2GC 2 bbl, Tri-Power 2 bbl, 94, 97 or 48 Stromberg carbs to any single venturi manifold. Includes carburetor adapter, gaskets, carb studs, nuts,...

Product#: MG1929

Holley 2300 2-Barrel to Rochester 4-Barrel Quadra-Jet Manifold Adapter Kit

Holley 2300 carburetor adapter kit for a Rochester 4-barrel intake manifold. This kit will adapt a large bolt pattern Holley 2300 to spread bore Rochester Q-Jet or Carter Thermo Quad 4-barrel manifold. The adapter is 1-1/8"...

Product#: MG1933

2-Barrel to 4-Barrel Carburetor to Manifold Adapter Kit

Square bore to 2-barrel carburetor to manifold adapter kit. This kit will adapt a 4-bolt 2-barrel flange to a 4-bolt square bore flange carburetor or manifold. It can be used to convert a 4-barrel manifold to 2-barrel or a...

Product#: MG1937

Holley 2300 2-Barrel to Rochester 2-Barrel Manifold Adapter Kit

Holley 2300 carburetor adapter kit for a Rochester 2-barrel inatke manifold. This kit will adapt a large bolt pattern Holley 2300 to small bolt pattern Rochester 2-barrel manifold. The adapter is 9/16" thick, constructed of...

Product#: ED8017

Ford Small-Block Windsor 302/5.0L 4V; EGR Valve Adapter Edelbrock Performer Intake Manifolds

Edelbrock EGR Adapter #8017 has made installing your new intake and carburetor easier on Ford 4V applications. When using Edelbrock EGR adapters, your existing EGR valve is repositioned to allow clearance for your carburetor....

Product#: ED8053

Ford Small-Block Windsor 302/5.0L 4V; 4 Barrel EGR Valve Spacer Plate

Edelbrock part #8053 is a 1" tall Ford 4V EGR adapter plate kit. This kit makes installing a new intake and carburetor much easier by repositioning the EGR valve to allow clearance for your carburetor. They're made of cast...

Product#: T2280

Holley Carburetor Spacer Set; 3/8" Tall Ported (No PVC Port)

Carburetor spacer kits are now available for Holley carburetors. Each kit includes mounting hardware and gaskets. {specs} {fitment}

Product#: H90060

1/16" Spread Bore Sealing Plate

Holley EFI spread bore sealing plate. This plate adapts a dual bolt pattern square bore carburetor or throttle body to a spread bore manifold and seal properly. Includes a 1/16" thick plate and two gaskets..