Product#: K521

1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models

OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...

Product#: 368077

1967-2002 Buick, Chevrolet, Pontiac, Oldsmobile; Accelerator Pedal Tension Spring; Various Car and Truck Models

This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...

Product#: AL124

Accelerator Throttle Rod; Universal Fit

Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...

Product#: TF100418

1955-57 Chevy Bel Air, Corvette, 150, 210, Nomad; Accelerator Pedal Pad

Correct reproduction accelerator pedal for 1955-57 Chevrolet Bel Air, 150, 210, and Nomad models. Each pad is manufactured to correct factory specifications replicating the original in design and fitment. Features correct...

Product#: 3923551

1968-69 Camaro Z28 Carb to Accelerator Lever Rod; 302 4 bbl

Reproduction accelerator pedal rod for 1968-69 Camaro Z/28 302 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...

Product#: 340637

1974-81 Outer Accelerator Pull Spring

Correct reproduction of the commonly missing or worn out outer accelerator pull spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Manufactured to exact factory...

Product#: 3923539

1968-69 327, 350 Carb to Accelerator Lever Rod; Small Block with 4 bbl Carb

Reproduction 1968-69 accelerator pedal rod for 327 or 350 engines with 4 bbl carburetors. This rod is the essential link between the accelerator pedal lever and the carburetor. Each rod is manufactured to correct...

Product#: 3909978

1967 Chevy, Pontiac; Accelerator Pad; with Steel Backing Plate; OE Style; Various Models

Reproduction of the original accelerator pedal pad designed for use on various 1967 GM models. This accelerator pedal pad is manufactured in the correct design based on a steel backing unlike the GM plastic replacements. The...

Product#: FM6098

Lokar Eliminator Brushed Billet Aluminum Floor Mount Gas Pedal with Rubber Inserts

The Eliminator floor-mount gas pedal is precision crafted from billet aluminum and designed to eliminate routing cables through the firewall. Includes an adjustable aluminum splined shaft and stainless steel under-the-floor...

Product#: FM6097

Lokar Eliminator Brushed Billet Aluminum Floor Mount Gas Pedal with Ball Milled Finish

The Eliminator floor-mount gas pedal is precision crafted from billet aluminum and designed to eliminate routing cables through the firewall. Includes an adjustable aluminum splined shaft and stainless steel under-the-floor...

Product#: BG6004

Lokar Black Anodized Aluminum Throttle Assembly Standard 1-1/2" x 4" Pedal Pad with Rubber Inserts

Gleaming polish not your style? Then take a look at this stealthy black anodized billet spring-loaded throttle assembly that features a removable lower arm and is splined for versatile mounting to either the right or left...

Product#: BAG6074

1955-57 Chevy Lokar Billet Accelerator Pedal Assemby - Small Block - Brushed w/Rubber Inserts

Lokar 1955-57 Chevy fullsize passenger car models billet aluminum throttle pedal assembly is designed to bolt into the stock location on the firewall, allowing yout o change from the factory rod linkage to a modern throttle...

Product#: BAG6073

1955-57 Chevy Lokar Billet Accelerator Pedal Assemby - Small Block - Ball Milled Finish

Lokar 1955-57 Chevy fullsize passenger car models billet aluminum throttle pedal assembly is designed to bolt into the stock location on the firewall, allowing you to change from the factory rod linkage to a modern throttle...

Product#: B199245

1958-67 Chevrolet; Billet Aluminum Floor Mount Gas Pedals; Black - Billet Specialties

These CNC machined pedal pads are specifically designed to compliment your Billet Specialties gas pedal. Each pad includes all the stainless steel hardware needed for a quick and clean install. {fitment}

Product#: B199250

1955-57 Chevrolet Passenger Car; Billet Aluminum Floor Mount Gas Pedals; Polished - Billet Specialties

These CNC machined pedal pads are specifically designed to compliment your Billet Specialties gas pedal. Each pad includes all the stainless steel hardware needed for a quick and clean install. {fitment}

Product#: B199240

1958-67 Chevrolet; Billet Aluminum Floor Mount Gas Pedals; Polished - Billet Specialties

These CNC machined pedal pads are specifically designed to compliment your Billet Specialties gas pedal. Each pad includes all the stainless steel hardware needed for a quick and clean install. {fitment}

Product#: TF801171

1994 & Later LT1/LT4 - Black Stainless Steel Lokar Throttle and Kickdown Cable Bracket Set

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Product#: SR4015

Lokar Throttle Cable Bracket Set - Ram Jet 350 Small Block - Black Stainless Steel

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: TF801170

1992-93 LT1 - Black Stainless Steel Lokar Throttle and Kickdown Cable Bracket Set

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Product#: SR4014

Lokar Throttle Cable Bracket Set - Ram Jet 350 Small Block - Stainless Steel

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: TF801167

1992-93 LT1 Lokar Stainless Steel Throttle and Kickdown Cable Bracket Set

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Product#: E8030

Edelbrock Small Block Chevy Throttle/Cruise Control/Kickdown Bracket - Chrome Plated

Edelbrock throttle, cruise control, and transmission kick down set for pre-1978 small block Chevy cars with a TH350, 200R4, or 700R4 transmission. Manufactured in stamped steel and either chrome or gold cadmium plated....

Product#: SR4012

Lokar Throttle Cable Bracket - 2000-02 LS1 Engines w/3-1/2" Throttle Linkage Cam - 1 Hole - Black

Black Billet Aluminum. Single Hole Stud For Throttle Cable Only. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor brackets...

Product#: TF801166

Lokar Throttle Cable Bracket - 1985-91 TPI Engines - Triple Hole - Black Finish

This billet aluminum cable bracket from Lokar mounts to the side of your TPI intake plenum and allow you to install your throttle cable. Made in USA Black billet aluminum. Triple hole stud for throttle, kickdown, and cruise...

Product#: SR4008

Lokar Throttle Cable Bracket - 1998-99 LS1 Engines w/3" Throttle Linkage Cam - Single Hole - Black

Black Billet Aluminum. Single Hole Stud For Throttle Cable Only. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor brackets...

Product#: SR4018

Lokar Throttle Cable Bracket - 2000-02 LS1 Engines w/3-1/2" Throttle Linkage Cam - 1 Hole - Brushed

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: SR4007

Lokar Throttle Cable Bracket - 1998-99 LS1 Engines w/3" Throttle Linkage Cam - Dual Hole - Brushed

Brushed Billet Aluminum. Dual Hole Stud For Throttle Cable & Cruise Control Cable. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more....

Product#: EL20835

1959-60 Impala, El Camino, Full Size; Accelerator Pedal Floor Bracket

Reproduction of the original accelerator pedal floor bracket for use with 1959-60 Chevrolet Impala and El Camino models. This accelerator pedal pivot bracket bolts to the floor. The accelerator pedal snaps down onto the ball...

Product#: DC2083

2 and 4 Bbl Holley Throttle Return Spring Set

Fits Holley 2300 and 2305 2 bbl. or Holley 4150 and 4160 4 bbl. carburetors mounted on any manifold. {fitment}

Product#: T9756

Chevrolet Small Block; Chrome Accelerator Cable Bracket; TH350

Chrome plated bracket set for Chevy small block with throttle cable type linkage. May be used with either round or square mounts. No need to remove carburetor for installation and allows for full adjustment. {specs} {fitment}

Product#: GPS6014

Lokar Billet Aluminum 3/4" Throttle Assembly Spacer

Pedal floor spacers are recommended when installing on vehicles with thick carpet or carpet padding. Made in USA

Product#: TF700440

1955-57 Chevy Bel Air, 150, 210, Nomad; Throttle Arm; with Bushings; V8

Reproduction of the original throttle arm designed for use with 1955-57 Chevrolet Bel Air, 150, 210, and Nomad 8 cylinder models. The throttle arm is manufactured in stamped steel to factory dimensions and replaces the...

Product#: C307911

1968-70 Camaro, Impala, Bel Air, Nova; Accelerator Pullback Spring Bracket; w/ 4 bbl. Carb

This is the retainer bracket which holds the rear loop of the throttle return spring in place. This bracket which mounts on top of the coil bracket was used on 1968-70 Camaro, Nova, Impala, Bel Air, and Caprice models with a...

Product#: TF700329

1955-57 Chevrolet Carburetor Return Spring ; V8 2bbl

Reproduction of the original carburetor spring designed for use on 1955-57 Chevrolet models with V8, 2 bbl carburetors. After you rebuild your original carburetor, be sure to make it perform properly. Don't get caught in a...

Product#: 154214

1955-1970 Accelerator Throttle Lever Arm Pinch Bolt Kit

Correct reproduction accelerator throttle lever to pedal rod pinch bolt kit, includes (1) 1/4-20 x 1-1/4" grade 5 bolt, nut & washer. GM Full Size passenger car applications: 1955-1970 Camaro applications: 1967-1969 Chevy...

Product#: TF700442

1955-57 Chevrolet 6 Cylinder 4 Piece Carburetor Linkage And Passing Gear Clip Set

Reproduction carburetor and passing gear linkage clips for 1955-57 Chevy models. Designed for 6 cylinder applications. Worn or missing clips should be replaced to ensure trouble-free operation. 4-piece set

Product#: TF700441

1955-57 Chevrolet 6 Cylinder 3 Piece Carburetor Linkage Clip Set

Reproduction carburetor linkage clips for 1955-57 Chevy models. Designed for 6 cylinder applications. Worn or missing clips should be replaced to ensure trouble-free operation. 3-piece set.

Product#: BAG6113

1955-57 Chevy - Lokar Billet Accelerator Pedal Assemby - Brushed Finish

Direct replacement billet aluminum pedal assemblies for 1955-57 Chevy full-size passenger models. Each throttle assembly has been designed to eliminate the factory rod linkage, utilize a modern Lokar throttle cable system and...

Product#: BAG6113B

1955-57 Chevy - Lokar Billet Accelerator Pedal Assemby - Black Finish

Direct replacement billet aluminum pedal assemblies for 1955-57 Chevy full-size passenger models. Each throttle assembly has been designed to eliminat e the factory rod linkage, utilize a modern Lokar throttle cable system...

Product#: BAG6112

1955-57 Chevy - Lokar Billet Accelerator Pedal Assemby - Ball Milled Finish

Direct replacement billet aluminum pedal assemblies for 1955-57 Chevy full-size passenger models. Each throttle assembly has been designed to eliminate the factory rod linkage, utilize a modern Lokar throttle cable system and...

Product#: B199155

Billet Specialties Billet Aluminum Cable Style Gas Pedal Assembly - Black

Add a touch of class to the interior of your Tri-Five Chevy with one of these CNC machined cable style gas pedal assemblies from Billet Specialties. These pedals convert your old linkage to a more modern cable style linkage...

Product#: B199150

Billet Specialties Billet Aluminum Cable Style Gas Pedal Assembly - Polished

Three piece universal billet aluminum pedal kits from Billet Specialties. These kits come with easy to use drill templates and all the necessary stainless steel hardware for installation.

Product#: BAG6074B

1955-57 Chevy Lokar Billet Accelerator Pedal Assemby - Small Block - Black w/Rubber Inserts

Lokar 1955-57 Chevy fullsize passenger car models billet aluminum throttle pedal assembly is designed to bolt into the stock location on the firewall, allowing yout o change from the factory rod linkage to a modern throttle...

Product#: BAG6004

Lokar Billet Aluminum Throttle Assembly Standard 1-1/2" x 4" Pedal Pad with Rubber Inserts

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Product#: BAG6001

Lokar Billet Aluminum Throttle Assembly with Standard 1-1/2" x 4" Pedal Pad and a Ball Milled Finish

This beautifully carved brushed billet aluminum throttle assembly has a spring-loaded pad like the OE design and features a splined removable lower arm for versatility in mounting to the right or left of the bracket. The...

Product#: SG6016

Lokar Chrome Steel Throttle Assembly with Extra Large 2" x 5" Pedal Pad and Rubber Inserts

The first spring loaded pedals in the industry! This chromed steel throttle assembly is spring loaded like the OE design, and features a removable, splined lower arm for versatile mounting to the right or left of the bracket...

Product#: SG6007

Lokar Chrome Steel Throttle Assembly with Standard 1-1/2" x 4" Pedal Pad and Rubber Inserts

The first spring loaded pedals in the industry! This chromed steel throttle assembly is spring loaded like the OE design, and features a removable, splined lower arm for versatile mounting to the right or left of the bracket...

Product#: B199255

1955-58 Chevrolet Passenger Car; Billet Aluminum Floor Mount Gas Pedals; Black - Billet Specialties

Add a touch of class to the interior of your Chevy with one of these CNC machined floor mount gas pedals from Billet Specialties. They are a simple bolt-in replacement for the stock pedal and can install in minutes. {fitment}

Product#: Y90491

1966-70 Impala; Caprice; Bel Air; Biscayne; Throttle Pedal Linkage Set; Upper and Lower; V8 or L6; 2 Piece

Reproduction gas pedal and throttle rod linkage set for 1966-70 Chevrolet full size passenger car models. This reproduction linkage set includes the lower interior rod that the gas pedal rest on and the engine side vertical...

Product#: SR4017

Lokar Throttle Cable Bracket & Spring Set - Big Block 502 - Black Stainless Steel

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: C90151

1955-57 Bel Air; 210; 150; Nomad; Throttle Pedal Linkage and Firewall Pivot Bracket Kit; V8 or L6

Reproduction gas pedal linkage rod and firewall pivot bracket for 1955-57 Chevrolet full size passenger car models. This reproduction linkage includes the lower interior rod that the gas pedal rest on and the firewall support...

Product#: TF801168

1994 & Later LT1/LT4 Stainless Steel Lokar Throttle and Kickdown Cable Bracket Set

Lokar's answer to LT cable problems. Stainless Throttle and Kickdown Brackets replace factory brackets. Kits include stainless arm to mount on throttle body to operate kickdown. Designed to be used with Lokar's Tuned-Port...

Product#: SR4016

Lokar Throttle Cable Bracket & Spring Set - Big Block 502 - Stainless Steel

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Finishes include stainless steel, black stainless steel & billet aluminum were...

Product#: SR4009

Lokar Throttle Cable Bracket - 1998-99 LS1 Engines w/3" Throttle Linkage Cam - Dual Hole - Black

Black Billet Aluminum. Dual Hole Stud For Throttle Cable & Cruise Control Cable. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more....

Product#: TF801164

1985-91 TPI Engines Lokar Throttle Cable Bracket - Single Hole - Black Finish

This billet aluminum cable bracket from Lokar mounts to the side of your TPI intake plenum and allow you to install your throttle cable. Made in USA Black billet aluminum. Single hole stud for throttle cable only.

Product#: SR4013

Lokar Throttle Cable Bracket - 2000-02 LS1 Engines w/3-1/2" Throttle Linkage Cam - 2 Holes - Black

Black Billet Aluminum. Dual Hole Stud For Throttle Cable & Cruise Control Cable. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more....

Product#: TF801165

1985-91 TPI Engine Lokar Throttle Cable Bracket - Double Hole - Black Finish

This billet aluminum cable bracket from Lokar mounts to the side of your TPI intake plenum and allow you to install your throttle cable. Made in USA Black billet aluminum. Double hole stud for throttle and ickdown cable only.

Product#: H2088

Holley; Throttle Cable Bracket

This chrome throttle cable bracket can be used with all 4150 and 4160 model square bore Holley carburetors. It includes dual stainless steel return springs.

Product#: SR4006

Lokar Throttle Cable Bracket - 1998-99 LS1 Engines w/3" Throttle Linkage Cam - Single Hole - Brushed

Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more. Carburetor brackets only fit Holley, Edelbrock, AFB, Quadrajet, Demon, & In-Line...

Product#: SR4011

Lokar Throttle Cable Bracket - 2000-02 LS1 Engines w/3-1/2" Throttle Linkage Cam - 2 Holes - Brushed

Brushed Billet Aluminum. Dual Hole Stud For Throttle Cable & Cruise Control Cable. Lokar throttle cable brackets are available for a variety of different motors including carbureted set ups, LS1, Ram Jet 350 & 502 and more....