Product#: K521

1949-82 GM; Accelerator Rod Grommet and Sleeve Set ; Various Models

OER® reproduction of the original accelerator rod grommet and sleeve unit where the accelerator rod fits into the linkage. This grommet often deteriorates due to engine heat or chemical spillage. Replacing the grommet will...

Product#: 368077

1967-2002 Buick, Chevrolet, Pontiac, Oldsmobile; Accelerator Pedal Tension Spring; Various Car and Truck Models

This is an OER® reproduction of the original type tension spring that will enable your gas pedal pad to position itself properly. This spring attaches under the pedal pad and attaches to the rod assembly to keep the pedal...

Product#: UK915

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 36" Long

This universal anti-squeak insulator set includes two rubber strips that insert in between the gas tank and the mounting straps to eliminate any noise from tank movement and vibration which may occur. One foam rubber pad...

Product#: AL124

Accelerator Throttle Rod; Universal Fit

Universal style accelerator throttle rod for various GM, Ford, Chrysler, Dodge, Plymouth models. This accelerator rod is for use when modifications will not allow the use of the original rod between the accelerator pedal...

Product#: YC111234A

1970-74 Chevrolet Corvette; Fuel Tank; With Flat Metal Valve; With EEC Bracket; Vent Pipe LH; Return Pipe RH; Zinc Coated; 18 Gallon Capacity

Reproduction fuel tank for 1970-1974 Chevrolet Corvette models. Each fuel tank is manufactured in quality stamped steel to original factory dimensions featuring a heavy zinc coating for corrosion resistance. Includes filler...

Product#: C67808

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps

Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...

Product#: CX5042

1965-97 GM; Fuel Tank Sending Unit; 0-90 Ohm; Universal Fit; For 6" to 24" Deep Fuel Tanks; Without Pick-Up Tube

Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...

Product#: 153665A

1946-02 GM; Various Models; Throttle Cable; 36""; Stainless Steel ; Cut-To-Fit

This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...

Product#: 153665B

Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black

This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...

Product#: 9047E

Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 15" Length

Reproduction fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 15" fuel hose to your...

Product#: 9047G

Fuel Filler Hose; Nitrile 70 Shore Rubber; 2" ID x 20" Length

Fuel filler hose to connect fuel neck to fuel tank on a variety of models requiring a 2" ID fuel hose. This hose can be used as is, or if you require a shorter piece, you can cut this 20" fuel hose to your desired length....

Product#: TF700512

Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.

Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...

Product#: YC111257

1968-74 Chevrolet Corvette; Fuel Tank Mounting Straps; EDP Coated; Galvanized Steel; Pair

Reproduction fuel tank mounting straps for 1968-1974 Chevrolet Corvette models. Each strap is manufactured in stamped steel to original to factory specifications. Produced in zinc plated steel with a black EDP coating for...

Product#: 9438225

1968-81 Corvette; Fuel Pump Return Hose

Replacement return hose for 1968-81 Corvette models. This 1/4" hose goes between the fuel pump and the tank.

Product#: 340637

1974-81 Outer Accelerator Pull Spring

Correct reproduction of the commonly missing or worn out outer accelerator pull spring which mounts between the carburetor and water neck and helps to return the throttle to the closed position. Manufactured to exact factory...

Product#: 14048

1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"

Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...

Product#: K915

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps

Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...

Product#: T76063

Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap

Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...

Product#: YC111246

1968-74 Chevrolet Corvette; Fuel Sending Unit; With Single 3/8" Outlet; Stainless Steel

Reproduction fuel sending unit for 1968-1974 Chevrolet Corvette models. Each sending unit is manufactured in stainless steel to correct factory specifications and replaced the old, or non working original exactly. This is a...

Product#: YC111253

1963-74 Chevrolet Corvette; Fuel Tank Filler Neck; 1963-1967 Convertible; 1968-74 All

Reproduction of the original style fuel tank filler neck designed for use with 1963-1967 Corvette Convertible, and all 1968-1974 Chevrolet Corvette models. Features correct mounting holes that match the original GM neck....