Product#: 152720

1970-81 Camaro/Firebird; Impala and other GM Models; Tail Light Harness Retaining Clips; Pair

Correct reproduction spring steel tail light harness retaining clips for various 1970-81 GM models. This clip attaches to the trunk wire gutter to secure the harness and keep it out of harms way while providing a clean...

Product#: 152718

1970-73 Camaro; Tail Lamp Wiring Clips; Small; Pair

Reproduction of the original correct style wiring harness retaining clip used on 1970-73 Camaro models. Manufactured to correct dimension in spring steel. This clip attaches to the tail lamp housings to secure the bulb wiring...

Product#: K236

1970-73 Chevrolet Camaro; Molded Tail Lamp Gasket Set; 4-Piece Set

Reproduction of the original tail lamp gaskets designed for use with 1970-73 Chevrolet Camaro standard and RS models. Each gasket set is molded in quality EPDM rubber that replicates the original in appearance, fit and...

Product#: *R408

Speed Nut 1/4" Self Thread Cutting - 12 Piece Set

Speed nuts are a great way of installing parts with studs onto the vehicle. These speed nuts are applied to the stud and pushed into the hole. The part is held in place by the self threading nut. 12 piece speed nut set is...

Product#: 5962696

1970-73 Camaro; Park Lamp Screw Set ; Standard; 8 piece Set

Reproduction of the original style shouldered lens screw set designed for use on various GM models including 1970-73 Camaros. Each screw is a replication of the original featuring chrome plating for corrosion resistance and...

Product#: UFM10

Electronic LED Flasher; For Tail Lights

This electronic LED flasher is recommended for use with LED tail lights. Two flashers are recommended. If you are installing both LED tail lights and LED front lights (turn signals etc.) TWO flashers are REQUIRED. LED...

Product#: A9100229

1970-81 Camaro, Firebird; Stop Lamp Bracket; with Nut and Bolt

Reproduction of the original stop lamp bracket designed for use with 1970-81 Camaro (except cruise control) and Firebird models.Each bracket is manufactured to factory specifications and includes correct nut and bolt. A must...

Product#: TF900626

Billet Aluminum Dual Filament Tail Lamp Sockets With Boots

These Ron Francis billet aluminum tail lamp sockets with weather protection boots (15" long) are ideal for classic vehicles! Uses a 3/4" mounting hole. Double Filament/staggered pins, typically uses 1157 or 1077 type bulbs.

Product#: TF900625

Billet Aluminum Single Filament Tail Lamp Sockets With Boots

These Ron Francis billet aluminum tail lamp sockets with weather protection boots (15" long) are ideal for classic vehicles! Uses a 3/4" mounting hole. Single filament/straight pins socket and typically uses 1156 or 1015...

Product#: C104

1966-69 Nova, 1967-68 Camaro RS; Park Lamp Lens Screw Set; Chrome Plated; 4 Piece Set

Reproduction of the original style shouldered lens park lamp lens screws designed for use with 1967-68 Camaro RS, 1966-69 Nova, and 1968 Impala, Bel Air, Biscayne, Caprice models. Each screw is chrome-plated for corrosion...

Product#: B10550

Chrome Plated Stainless Steel Shouldered Lens Screws, #8-32 x 1-5/16" With 15/16" Shoulder, 4 Piece Set

Reproduction shouldered lens screw set, chrome-plated stainless steel for superior corrosion resistance and outstanding appearance. 4 piece set. Replacement lens screws used on various GM vehicles. Available in standard or...

Product#: K5242

Shouldered Lens Screw ; Chrome Plated ; 6 Piece Set ; Turn Signal, Tail Lamp, Side Marker Lens

Reproduction shouldered lens screw set, chrome-plated stainless steel for superior corrosion resistance and outstanding appearance. Replacement lens screws used on various GM vehicles. Most 1965 and later GM vehicles used...

Product#: 9432461

Hex Flanged Stamped Steel Thread Cutting Nut; .88mm Diameter; With Mastic Sealant; Set of 8

Reproduction stamped steel thread cutting nut set for a variety of applications including for use to secure the tail light bezels on 1974-78 Firebird and other models. Can be used anywhere on your car where a 1/4" post...

Product#: *A2896K

Thread Cutting Pal Nut, 3/16" Stud Size, Hex Washer Head, Zinc Plated

Replacement thread cutting pal-nuts used on various GM vehicles. Hex washer head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...

Product#: *A3405K

Thread Cutting Pal Nut, 1/4" Stud Size, Hex Washer Head, Zinc Plated, 10 Piece Set

Replacement thread cutting pal-nuts used on various GM vehicles. Hex washer head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...

Product#: *R406

Speed Nut 1/4" Self Threading Nut Retainer Set - Set of 6

Speed nuts are a great way of installing parts with studs onto the vehicle. These speed nuts are applied to the stud and pushed into the hole. The part is held in place by the self threading nut. 6 piece speed nut set is...

Product#: K5241

Park Lamp Lens Screw Set ; Chrome ; 4 Piece Set ; Turn Signal, Tail Lamp, Side Marker

Reproduction shouldered lens screw set, chrome-plated stainless steel for superior corrosion resistance and outstanding appearance. Replacement lens screws used on various GM vehicles. Most 1965 and later GM vehicles used...

Product#: MA2098

Chrome Plated Standard Lens Screws, #8-32 x 13/16", 1969 Dart Park Lamp Lens Screw Set - 4 Piece

Reproduction standard lens screw set, chrome-plated stainless steel for superior corrosion resistance and outstanding appearance. 4 piece set. Reproduction of the 1969 Dart park lamp lens screws. Replacement lens screws...

Product#: *A10733K

Thread Cutting Pal Nut, 5/16" Stud Size, Hex Washer Head, Zinc Plated, 10 Piece Set

Replacement thread cutting pal-nuts used on various GM vehicles. Hex washer head, zinc plated. Mastic sealer washers sold separately. Correct hardware can make any installation job easier. Replace your missing or damaged...

Product#: 3982098

U-Type Extruded Clip Nut, Fits 1/4-20 Bolts, Black Phosphate Coated

Replacement U-clip nuts used on various GM vehicles. Black phosphate coated. Quantities vary by model. Use as needed. This is the correct nut used to install the rear tail lamp to the body. Can be used to install the rear...