Product#: PX40011

Pertronix Flame Thrower 8-Cylinder 40,000 Volt 1.5 Ohm Black Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: 7720

MSD; Power Grid 7; Ignition Control Only

The Power Grid Ignition Control has been specially designed to mount to the Power Grid System Controller box, part #7730/77303. This Ignition output only controller packs higher output than the current programmable...

Product#: 77303

MSD; Power Grid System; Controller Only; Black

The Power Grid Ignition System is the next evolution of our Programmable 7-Series Ignition Controls. The Grid incorporates an efficient 32 bit microcontroller and an all new software program, called MSD View, and is USB...

Product#: 8253

MSD; Blaster HVC II Ignition Coil; Blue

The latest coil to be built entirely in house at MSD is designed to be used with MSD 6 and SCI Series Ignition Controls. This coil utilizes an iron U-Core design with a segmented bobbin for improved voltage distribution. The...

Product#: 8252

MSD; Blaster HVC Ignition Coil; Blue; Universal

Coils have always had to compromise voltage output against current output. More voltage increases the initial ionization of the spark plug gap, but lowers the amount of current, or heat, that follows across the plug gap. When...

Product#: 75643

MSD; Stand Alone Solid State Relay Kit; 4 Channel; Black

Clean up your wiring with an MSD Solid State Relay Block. This module takes the place of 4 standard relays and eliminates unsightly wiring. 4 independent channels can be activated using either power or ground. Each channel is...

Product#: 7740

MSD; Power Grid CAN-Bus 4-Hub Connector; Red

This hub allows you to expand the Power Grid system with up to four accessory modules.Note: This part is legal for use on Uncontrolled (Non-Emissions Controlled) Vehicles or Racing Vehicles.

Product#: PX60104

Pertronix 60,000 Volt 0.45 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it...

Product#: PX60130

Pertronix 60,000 Volts 3.0 Ohm Flame Thrower HV Ignition Coil

The Flame Thrower HV (high voltage) coil has an E-Core design which is rated at a sizzling 60,000 volts and operates with no degradation of energy throughout the temperature ranges. Made from 6063 T5 aluminum, it...

Product#: 140001

Accel; 1955-74; 45,000 Volt; Super Coil; Ignition Coil

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability. {specs}

Product#: 8732

MSD; Digital 2-Step Rev Control; For Digital 6AL

This 2-Step Rev Control could be added to give you the ability to switch to a low rpm limit to use on the starting line. Features two easy to read rotary dials that let you set the launch rpm in 100 rpm increments. There is...

Product#: PX60103

Pertronix 60,000 Volt 0.32 Ohm Flame Thrower HC Ignition Coil

The Flame Thrower HC (high current) coil has an E-Core design which is rated at 60,000 volts with an ultra low .32 primary resistance and has a High Current design for a rapid charge rate. Made from 6063 T5 aluminum, it...

Product#: PX45111

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...

Product#: PX44001

Pertronix Flame Thrower III 8 Cylinder 45,000 Volt 0.32 Ohm Chrome Oil Filled Ignition Coil

The Flame Thrower III Coil is a rapid charge ignition coil to optimize the Ignitor III module. The Flame Thrower III is a traditional oiled filled canister for the "old school" appearance; but will work with modern day...

Product#: PX44011

Pertronix Flame Thrower III 8 Cylinder 45,000 Volt 0.32 Ohm Black Oil Filled Ignition Coil

The Flame Thrower III Coil is a rapid charge ignition coil to optimize the Ignitor III module. The Flame Thrower III is a traditional oiled filled canister for the "old school" appearance; but will work with modern day...

Product#: PX40111

PerTronix Flame Thrower 8 Cylinder 40,000 Volt 1.5 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: PX45001

Pertronix Flame Thrower II 4 -6 - 8 Cylinder 45,000 Volt 0.6 Ohm Chrome Oil Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower II high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel...

Product#: 8145

Accel; 1955-74; Yellow; 45,000 Volt; Superstock Breakerless Electronic Ignition Coil

Replace your stock coil with an Accel high performance coil for increased performance, longer life and maximum dependability. {specs}

Product#: PX40611

Pertronix Flame Thrower 6 Cylinder 40,000 Volt 3.0 Ohm Black Epoxy Filled Ignition Coil

Complete your ignition upgrade with a Flame Thrower high performance ignition coil! The Flame Thrower coil fits into your existing coil bracket for a clean, factory look. Enables larger plug gaps for greater fuel efficiency...

Product#: 86415

MSD; 6EFI; Ignition Coil; For Part # 6415

When running an MSD Atomic EFI or similar throttle body fuel injection system with a 6EFI ignition box, the 6EFI ignition coil is made for you. Designed to match the 6EFI ignition, the 6EFI coil has a clean black appearance...