Vintage Air Gen 5 Magnum Universal Evaporator Kit w/ Heat, Cool, & Defrost
The Gen 5 is Vintage Air's most powerful and intelligent climate control system. The Gen 5 uses an exclusive fully electronic microprocessor control system that eliminates cables or vacuum connections. Separate high-capacity...
Vintage Air Gen 5 Magnum Universal Evaporator Kit w/ Heat, Cool, & Defrost
Classic $1111.99 ea
March Performance; Sanden 508 AC Compressor; 7-Groove Serpentine; R134A Refrigerant; Polished
The March Performance Air Conditioning Compressors are just what you need to make a "hot" rod cool and comfortable to drive around on hot summer nights! These show quality compressors are offered in either polished or chrome...
March Performance; Sanden 508 AC Compressor; 7-Groove Serpentine; R134A Refrigerant; Polished
Classic $439.99 ea
Sanden SD 508 Rear Exit Compressor; Double V-Groove Pulley; Rear Exit; Standard Finish
Sanden SD 508 rear exit compressor, double V-groove pulley, rear exit with a standard finish. Excellent solution to low hood clearance issues. SD 508 compressor with rear exit #8 and #10 male 0-ring fittings. Compatible with...
Sanden SD 508 Rear Exit Compressor; Double V-Groove Pulley; Rear Exit; Standard Finish
Classic $243.99 ea
Sanden 508 A/C Compressor; w/ 2-Groove V-Belt Clutch Pulley; Natural Finish; SD508; Vintage Air
The SD 508 compressor is recommended for any Vintage Air system. It pumps 8.4 cubic inches per revolution with a maximum 6000 sustained RPM range. Available in standard finish or polished as shown. Fits all Vintage Air...
Sanden 508 A/C Compressor; w/ 2-Groove V-Belt Clutch Pulley; Natural Finish; SD508; Vintage Air
Classic $243.99 ea
Serpentine Pulley/Clutch Sanden Style
March Performance serpentine pulley and clutch for Sanden style 508 compressor. Perfect for converting your existing compressor from v-belt to serpentine. Note: No further discounts apply.
AC Compressor Manifold with Polished Finish; March 418-05
Custom AC compressor manifold for March Performance pulley sets with Sanden 7176 compressors. It reroutes the compressor lines downward where they are less visible and less vulnerable to exhaust heat. Important: Designed for...
1998-Up LS1, LS2, LS3 & LS6 With Short Water Pump Inboard Mount AC Compressor Only Bracket Set
Made of billet aluminum and beautifully polished, this bracket is adjustable up to 3/4" before and after for perfect alignment, and designed to eliminate component vibration. This inboard mount set is for use on vehicles...
AC Compressor Manifold with Black Finish; March 418-08
Custom AC compressor manifold for March Performance pulley sets with Sanden 7176 compressors. It reroutes the compressor lines downward where they are less visible and less vulnerable to exhaust heat. Important: Designed for...
Polished Aluminum A/C Drier; with Bracket
Features a unique design which allows changing the drier without removing any fittings 2.5 IN. x 7 IN. (Inlet on left side).
Chrome Drier with Bracket. Features a built in mounting bracket and compact size 2.5 IN. x 6 IN.
1964-72 Small Block Front A6 Compressor Brace
Reproduction front air conditioning compressor brace designed for models with a small block and A6 AC compressor. Camaro applications: 1967 small blocks with short water pump and stock exhaust manifolds Chevrolet / GMC Truck...
GM A-6 to R4 Compressor Block Fitting Adapter
OEM compressor refrigerant line O-ring adapters. GM A-6 and R4 complete kit. Kit includes GM A-6 and R4 early-style compressor adapter block kit with bolt and O-rings (34108-VUG), GM A-6 and R4 offset flange pad seal washer...
1962-85 GM Compressor Oil Pump
Compressor Internal Oil Pump: Rebuild your original compressor. The internal oil pump assembly originally installed on axial style air conditioning compressors. Consists of an 1 inner and 1 outer rotor.
O-Ring Seal Set; Air Conditioning Compressor Seals
Replacement O-ring set or evaporator core housing seal set for various GM models. The O-ring in the set measures 5-1/64" x 9/64" thick. Sold individually. Replaces OE #'s 6558587, 19188276, 2724674. Product Specifications:...
1962-75 GM Comp Cyl Locator Pin
Compressor Cylinder Locator Pin: Correct cylinder locating pin used for the compressor cylinder. For use on all 1962-85 axial compressors.
Vintage Air Gen 5 Super Magnum Universal Evaporator Kit w/ Heat, Cool, & Defrost
The Gen 5 is Vintage Air's most powerful and intelligent climate control system. The Gen 5 uses an exclusive fully electronic microprocessor control system that eliminates cables or vacuum connections. Separate high-capacity...
Vintage Air Gen 5 Super Magnum Universal Evaporator Kit w/ Heat, Cool, & Defrost
Classic $1164.99 ea
Monster Trunk Vacuum System - Cool Only
This trunk-mounted system delivers in mass volume and is great for larger cars. Molded dual louvers mount to back seat package tray. Switch pod mounts under the dash. May be used as part of a dual air system too.
Sanden SD-7B10 Front Runner; Compressor; 6-groove; Serpentine Pulley Chrome Finish
Sanden SD-7B10 front runner compressor 6-groove serpentine pulley chrome finish. Compact but high-performance compressor used on our award-winning Front Runner Accessory Drive systems. It pumps 6.1 cubic inches per revolution...
Sanden SD-7B10 Front Runner; Compressor; 6-groove; Serpentine Pulley Chrome Finish
Classic $423.99 ea
Sanden SD 508 Compressor 7-Groove; Serpentine Pulley; Chrome Finish
The SD 508 compressor is recommended for any Vintage Air system. It pumps 8.4 cubic inches per revolution with a maximum 6000 sustained RPM range. Available in standard finish or polished as shown. Fits all Vintage Air...
Sanden SD 508 Compressor 7-Groove; Serpentine Pulley; Chrome Finish
Classic $424.99 ea
Sanden SD 508 Rear Exit Compressor; 7-Groove Serpentine Pulley; Rear Exit; Polished Finish
Excellent solution to low hood clearance issues. SD 508 compressor with rear exit #8 and #10 male 0-ring fittings.Compatible with standard female O-ring fittings. Also 90-degree TiteFit fittings.
Sanden SD 508 Rear Exit Compressor; 7-Groove Serpentine Pulley; Rear Exit; Polished Finish
Classic $348.99 ea
Sanden 709 7-Groove Serpentine Belt 134A; AC Compressor; Natural Finish
Vintage Air standard finish Sanden SD 709 air conditioning compressor w/ 7-groove serpentine belt pulley. The SD 709 compressor is compatible with any Vintage Air system and fits all Vintage Air brackets. It pumps 9.5 cubic...
Sanden 709 7-Groove Serpentine Belt 134A; AC Compressor; Natural Finish
Classic $258.99 ea
Vintage Air Sanden 709 Double V-Groove 134A AC Compressor - Natural Finish
Vintage Air standard finish Sanden SD 709 air conditioning compressor w/ double V-groove V-belt clutch pulley. The SD 709 compressor is compatible with any Vintage Air system and fits all Vintage Air brackets. It pumps 9.5...
Vintage Air Sanden 709 Double V-Groove 134A AC Compressor - Natural Finish
Classic $258.99 ea
Sanden 508 AC Compressor - 7 Groove Serpentine Pulley - Natural Finish
Sanden SD 508 Compressor 7-Groove serpentine pulley Standard Finish. The SD 508 compressor is recommended for any Vintage Air system. It pumps 8.4 cubic inches per revolution with a maximum 6000 sustained RPM range. Fits all...
Sanden 508 AC Compressor - 7 Groove Serpentine Pulley - Natural Finish
Classic $243.99 ea
This compressor bracket system is designed to replace the factory A/C compressor with an aftermarket Sanden compressor. A/C compressor is driven off the factory inner four grooves of the LS1 Camaro harmonic balancer. Bracket...
SuperFlow Horizontal AC Condenser; 14" x 22"; Universal Fit
Horizontal SuperFlow Condenser with brackets 14 IN. tall x 22 IN. wide x.83 IN. thick. Perfect for late-model cars with more grill area. With male O-ring fittings. Top NO 8 bottom NO 6.
New, not rebuilt, Sanden SD706 / SD7B10 peanut style air conditioning compressor. The compact SD7B10 is becoming one of the most popular compressors for original equipment manufacturers or aftermarket. SD706s rob less...
March Performance AC Compressor Manifold with Chrome Finish; March 418-06
Custom AC compressor manifold for March Performance pulley sets with Sanden 7176 Sanden compressors. It reroutes the compressor lines downward where they are less visible and less vulnerable to exhaust heat. Important:...
March Performance AC Compressor Manifold with Chrome Finish; March 418-06
Classic $149.99 ea
Vintage Air Steel-eez top-mount compressor bracket kit for generation I Chevrolet small-block engines with short water pumps. Mounts for compressor and alternator. Fits Chevy cylinder heads without bolt holes. Bolts to water...
1947-50 Chevy Pickup Truck; Top Mount Compressor & Alternator Bracket Kit; Small-Block Chevy; RH Passenger Side; Vintage Air
Classic $126.99 set
Vintage Air Small Block Engine And Long Water Pump - Compressor Mounting Bracket (Passenger Side)
Mounts compressor to Chevy cylinder heads without bolt holes. Bolts water pump to intake manifold, and clearsd tall valve covers. Note: No further discounts apply.
Vintage Air Small Block Engine And Long Water Pump - Compressor Mounting Bracket (Passenger Side)
Classic $126.99 ea
Standard Painted A/C Drier; with Trinary Switch & Mounting Hardware; Black; 2.5" x 6"; Universal
This standard drier is painted black and features a trinary safety switch along with all necessary mounting hardware. Dimensions are 2.5 x 6". No adapter needed.
Standard Painted A/C Drier; with Trinary Switch & Mounting Hardware; Black; 2.5" x 6"; Universal
Classic $76.99 ea
1947-2008 Standard Economy Air Conditioner Drier; Black Painted; 2.5" x 6"; Various Models
This economical drier is painted black and has a threaded port for trinary or binary switch installation. Comes sealed and pre-charged with nitrogen. Dimensions are 2.5 x 6. NOTE: Brackets available separately. Equipped with...
1947-2008 Standard Economy Air Conditioner Drier; Black Painted; 2.5" x 6"; Various Models
Classic $39.99 ea
This steel air conditioning bracket relocates the air conditioning compressor to the left of the engine. Designed to allow clearance for headers in specific pre-1979 small block Chevy applications.
O-Ring Seal; Air Conditioning Compressor Seal
Replacement O-ring or evaporator core housing seal for various GM models. This O-ring for the housing seal measures 51/64" x 9/64" thick. Sold individually. Replaces OE #'s 6558587, 19188276, 2724674. Product Specifications:...
Vintage Air O-ring adapter fitting for Sanden SD-7 "Peanut" style compact AC compressors. This aluminum adapter will bolt directly to the suction inlet flange, converting it to #8 and #10 male O-ring thread. Sold...
Sanden SD-7B10 / 7176 Peanut Style Compressor Discharge Adapter Fitting; Straight w/ #8 and #10 O-Ring; Black
Classic $49.99 ea
1998-Up LS1 Small Block With Short Water Pump Inboard Mount Alternator And AC Compressor Bracket Set
This Zoops Correct-Align adjustable alternator and AC compressor bracket set features bolt-on installation with no drilling required. Made of billet aluminum and beautifully polished, these brackets are adjustable up to 3/4"...
1998-Up LS1 Small Block With Short Water Pump Inboard Mount Alternator And AC Compressor Bracket Set
Classic $319.99 set
Old Air Products; York to Sanden 508 A/C Compressor Mounting Bracket Claw Adapter
Mounts Sanden 508 or equivalent compressor to most factory brackets originally designed for York or Tecumseh compressors. Also commonly used to fabricate custom brackets. Hardware is included.
Old Air Products; York to Sanden 508 A/C Compressor Mounting Bracket Claw Adapter
Classic $89.99 ea
Custom curved adapter manifold fitting for Sanden SD-7 "Peanut" style compact AC compressors. This aluminum adapter will bolt directly to the suction inlet flange, converting it to #8 and #10 male O-ring thread. Sold...
Sanden SD-7B10 / 7176 Peanut Style Compressor Discharge Adapter Fitting; Straight w/ #8 and #10 O-Ring; Black
Classic $59.99 ea
Old Air Products; York to Sanden 508 A/C Compressor Mounting Bracket Adapter
Adapts Sanden 508 style compressor to an original York mounting bracket. Use with original bracket, idlers and belt tensioner. Also commonly used to fabricate custom brackets. Kit includes hardware to mount Sanden style...
Old Air Products; York to Sanden 508 A/C Compressor Mounting Bracket Adapter
Classic $59.99 ea
Custom curved adapter manifold fitting for Sanden SD-7 "Peanut" style compact AC compressors. This aluminum adapter will bolt directly to the suction inlet flange, converting it to #8 and #10 male O-ring thread. Sold...
Sanden SD-7B10 / 7176 Peanut Style Compressor Discharge Adapter Fitting; Straight w/ #8 and #10 O-Ring; Black
Classic $59.99 ea
Reproduction 2 1/4" heater hose bracket for a wide variety of GM models from 1938-93. This hose bracket is designed to secure two heater hoses to the alternator bracket to prevent damage of the hoses and keep the engine...